功能安全性參數: |
MTTFd |
110 a |
Mission Time (TM) |
20 a |
L10h |
1.9 E+11 at 6000 rpm and 20/40 N axial/radial shaft load |
Diagnostic Coverage (DC) |
0 % |
電氣特性: |
Operating voltage |
10 ... 30 V DC |
No-load supply current |
max. 140 mA |
Power consumption |
≤ 2.5 W , without output drivers |
Linearity |
± 0.5 LSB |
Output code |
Gray code, binary code |
Code course (counting direction) |
cw ascending (clockwise rotation, code course ascending) |
Code preparation time |
0.3 ms |
接口: |
Interface type |
Push-pull, parallel , short-circuit protected |
Resolution |
|
|
Multiturn |
25 Bit |
Load current |
20 mA |
Voltage drop |
≤ 2.5 V |
Signal voltage |
|
|
High |
operating voltage minus voltage drop |
|
Low |
≤ 2.8 V |
Rise time |
300 ns |
De-energized delay |
300 ns |
Code change frequency |
400 kHz |
輸入 1: |
Input type |
Selection of counting direction (cw/ccw) |
Signal voltage |
|
|
High |
10 ... 30 V |
|
Low |
0 ... 2 V |
Input current |
< 6 mA |
輸入 2: |
Input type |
Temporary storage (LATCH) |
Signal voltage |
|
|
High |
10 ... 30 V |
|
Low |
0 ... 2 V |
Input current |
< 6 mA |
Switch-on delay |
< 0.1 ms |
Switch-off delay |
< 0.1 ms |
輸入 3: |
Input type |
zero-set (PRESET) |
Signal voltage |
|
|
High |
10 ... 30 V |
|
Low |
0 ... 2 V |
Input current |
< 6 mA |
Switch-on delay |
< 1 ms |
連接: |
Connector |
type 9426, 26-pin |
Cable |
∅9 mm, 15 x 2 x 0.14 mm2, 2 m |
符合標準: |
Degree of protection |
DIN EN 60529, IP65 |
Climatic testing |
DIN EN 60068-2-3, no moisture condensation |
Emitted interference |
EN 61000-6-4:2007 |
Noise immunity |
EN 61000-6-2:2005 |
Shock resistance |
DIN EN 60068-2-27, 100 g, 6 ms |
Vibration resistance |
DIN EN 60068-2-6, 10 g, 10 ... 2000 Hz |
許可和認證: |
UL approval |
cULus Listed, General Purpose, Class 2 Power Source |
周圍環境: |
Operating temperature |
-40 ... 85 °C (-40 ... 185 °F)
cable models:
-30 ... 70 °C (rigid wiring)
-5 ... 70 °C (flexible wiring) |
Storage temperature |
-40 ... 85 °C (-40 ... 185 °F) (cable models: -5 ... 70 °C) |
機械特性: |
Material |
|
|
Combination 1 |
housing: powder coated aluminum
flange: aluminum
shaft: stainless steel |
|
Combination 2 (Inox) |
housing: stainless steel
flange: stainless steel
shaft: stainless steel |
Mass |
approx. 400 g (combination 1)
approx. 800 g (combination 2) |
Rotational speed |
max. 12000 min -1 |
Moment of inertia |
30 gcm2 |
Starting torque |
≤ 5 Ncm |
Shaft load |
|
|
Axial |
40 N |
|
Radial |
110 N |